What is a crosswind?
A crosswind is a wind component that acts at right angles to the runway centre line. It pushes an aircraft sideways during takeoff and landing.
Definition
The International Civil Aviation Organization (ICAO) calls it the crosswind component. ICAO Annex 14 Volume I defines it as the surface wind component at right angles to the runway centre line. The European Union Aviation Safety Agency (EASA) uses the same words.
Most runways see winds that blow at an angle to the runway and not along it. Every wind that is not parallel to the runway has a crosswind part. The rest of the wind acts along the runway. It is a headwind component if it blows toward the aircraft nose, or a tailwind component if it blows from behind.
Wind direction is the direction that the wind blows from. A wind from 090 degrees comes from the east. In a weather report, the wind is three digits in tens of degrees, then the speed in knots (kt). The letter G adds the gust. The report 08032G45KT means a wind from 080 degrees at 32 knots, with gusts to 45 knots (FAA Aeronautical Information Manual).
How to calculate a crosswind
The crosswind component equals the wind speed times the sine of the angle between the wind direction and the runway direction (FAA AC 150/5300-13B, B.3.1). The headwind component equals the wind speed times the cosine of the same angle.
- Crosswind = wind speed x sin (angle)
- Headwind = wind speed x cos (angle)
A 20 knot wind at 60 degrees to the runway gives a crosswind of 20 x 0.866 = 17 knots. The headwind part is 20 x 0.5 = 10 knots. The FAA uses this example in AC 150/5300-13B.
Take a runway with a magnetic heading of 180 degrees (runway 18) and a wind of 40 knots from 210 degrees. The angle is 30 degrees. The crosswind is 40 x 0.5 = 20 knots. The headwind is 40 x 0.866 = 35 knots.
| Angle between wind and runway | Sine | Crosswind as a share of the wind |
|---|---|---|
| 10 degrees | 0.17 | 17 % |
| 20 degrees | 0.34 | 34 % |
| 30 degrees | 0.50 | 50 % |
| 45 degrees | 0.71 | 71 % |
| 60 degrees | 0.87 | 87 % |
| 90 degrees | 1.00 | 100 % |
A wind at 30 degrees has a crosswind of half its speed. A wind at 90 degrees has a crosswind of its full speed. One knot is 1.852 km/h, so 20 knots is 37 km/h. The page on the crosswind component has more worked examples, a tailwind case and a gust case.
Effect on aircraft
An airborne airplane moves with the air mass in which it flies. A crosswind makes it drift sideways across the runway unless the pilot corrects for it. On the ground the airplane cannot move with the air mass. An airplane has more side area behind the main wheels than in front of them, so it tends to turn into the wind. This is weathervaning. The upwind wing also receives a greater force from the wind than the downwind wing (FAA Airplane Flying Handbook, Chapter 9).
If an airplane touches down while it moves sideways, the landing gear takes a side load. The pilot must remove the drift before touchdown, or keep the airplane aligned with the runway during the whole approach.
Takeoff and landing technique
In a crosswind takeoff, the pilot applies aileron pressure into the crosswind. This keeps the upwind wing from rising. The deflected ailerons and rudder add drag, so the pilot should expect less takeoff performance (FAA Airplane Flying Handbook, Chapter 6). In a significant crosswind, the pilot holds the main wheels on the ground slightly longer than normal. The aircraft then lifts off cleanly.
The FAA names two usual methods for a crosswind landing:
- Crab method. The pilot points the nose into the wind so that the ground track follows the runway centre line. Just before touchdown, the pilot uses rudder to align the airplane with the runway. A change that is too early or too late causes a side load.
- Wing-low method. The pilot aligns the heading with the runway with rudder. The pilot then banks into the wind with aileron by just enough to stop the drift. The upwind main wheel touches down first.
The FAA recommends the wing-low method in most cases, and a combination of both methods is possible. It states that crosswind landings are a little harder than crosswind takeoffs.
Aircraft limits
Before the Federal Aviation Administration (FAA) type certificates an airplane, a flight test must show control in 90 degree crosswinds. The test speed is up to 0.2 times the power-off stall speed in landing configuration. The pilot needs no exceptional skill or alertness for it. An airplane that stalls at 50 knots in landing configuration gets 0.2 x 50 = 10 knots. Airplanes certificated after 3 May 1962 carry the value on a placard (FAA Airplane Flying Handbook, Chapter 9).
For transport airplanes, 14 CFR 25.237 requires a demonstrated 90 degree crosswind for dry runways. It must be at least 20 knots or 0.2 VSR0, whichever is greater. It need not exceed 25 knots.
This is a demonstrated value and not a limit. Most aircraft publish only the demonstrated crosswind and no maximum crosswind. On a contaminated runway, tire cornering limits can reduce braking. The crosswind can then dominate the landing distance assessment (FAA AC 91-79B, 3.10). The FAA says that pilots must find the maximum crosswind component of each airplane and avoid wind conditions above its capability. If the wind exceeds the allowable crosswind, the pilot may divert on approach or wait before departure (AC 150/5300-13B, B.1.1).
Reading the wind
Wind reports use different north references. A weather report in the METAR format gives the wind direction from true north. The tower and the automatic terminal information service (ATIS) give it from magnetic north. A runway number is the magnetic azimuth rounded to the nearest 10 degrees. When you calculate a crosswind from a METAR wind, convert the wind direction or the runway heading first. The FAA wind coverage method does the same, because its wind data are true and its runway headings are magnetic (AC 150/5300-13B, B.4.1).
Runway orientation and wind coverage
ICAO Annex 14 recommends a usability factor of at least 95 percent for the aeroplanes that an aerodrome serves. The number and orientation of the runways should achieve it. The usability factor is the percentage of time during which the crosswind component does not restrict the use of a runway. EASA gives the same 95 percent as guidance material.
For this calculation, ICAO assumes that landing and takeoff are normally not possible above these crosswind components:
- 37 km/h (20 kt) for a reference field length of 1 500 m or more. It is 24 km/h (13 kt) if poor braking action occurs often.
- 24 km/h (13 kt) for a reference field length of 1 200 m up to but not including 1 500 m.
- 19 km/h (10 kt) for a reference field length below 1 200 m.
These are Recommendations. The calculation uses mean winds, from wind statistics that cover as long a period as possible, preferably not less than five years. EASA lists the factors that can require lower values. They are gusts, turbulence, a secondary runway, runway width, water, snow or ice on the runway, and the strength of the wind.
The FAA uses 95 percent wind coverage with at least ten consecutive years of wind data. It sets the allowable crosswind by Runway Design Code (RDC):
| Runway Design Code | Allowable crosswind |
|---|---|
| A-I and B-I | 10.5 knots |
| A-II and B-II | 13 knots |
| A-III, B-III and C-I through D-III | 16 knots |
| A-IV and B-IV, C-IV through D-VI, E-I through E-VI | 20 knots |
If the primary runway gives less than 95 percent, the FAA evaluates the need for a crosswind runway. It designs one when the critical aircraft that needs the coverage is in regular use. If a second runway is impractical, the FAA accepts a wider primary runway. The FAA does not consider gusts in its wind coverage review. A coverage below 100 percent is not a deficiency (AC 150/5300-13B, Appendix B).
What it means on an airfield
An aerodrome must have at least one wind direction indicator. It is a fabric cone that shows the surface wind direction and gives a general indication of wind speed (ICAO Annex 14, 5.1.1). ICAO recommends that at least one indicator is lit at an aerodrome that operates at night. EASA notes that cones that extend fully at about 15 knots are most useful. This is the maximum crosswind landing component for small aircraft.
EASA also notes that strong crosswinds can move an aircraft far from the runway centre line. This is a reason to consider runway shoulders. The same guidance lists inset runway edge lights and extra runway centre line guidance as mitigation measures.
TarmacView inspects airfield lighting with a drone. It does not measure wind or crosswind.
Frequently Asked Questions
- What is a crosswind in aviation?
- A crosswind is the part of the wind that acts at right angles to the runway centre line. A wind that blows along the runway has no crosswind. A wind that blows across the runway has all of its speed as crosswind. A wind at any other angle has a crosswind part and a headwind or tailwind part.
- What is the crosswind formula?
- Crosswind = wind speed x sine of the angle between the wind direction and the runway direction. A 20 knot wind at 60 degrees to the runway gives 20 x 0.866 = 17 knots of crosswind. The headwind part is 20 x cosine 60 = 20 x 0.5 = 10 knots.
- What is a crosswind runway?
- A crosswind runway is a second runway at an angle to the primary runway. Planners evaluate the need for one when the primary runway gives less than 95 percent wind coverage. The FAA also accepts a wider primary runway in place of a crosswind runway where a second runway is impractical or cost prohibitive.
- How do pilots land in a crosswind?
- They use the crab method, the wing-low method, or a combination of both. In the crab method the pilot points the nose into the wind and removes the crab with rudder just before touchdown. In the wing-low method the pilot keeps the nose aligned with the runway and banks into the wind to stop the drift. The FAA recommends the wing-low method in most cases.
- What is the maximum crosswind for landing?
- There is no single value. Each aircraft type has its own demonstrated crosswind, and most aircraft publish only that value and no maximum limit. For transport airplanes, 14 CFR 25.237 sets a demonstrated 90 degree crosswind. It is at least 20 knots or 0.2 VSR0, whichever is greater. It need not exceed 25 knots. A contaminated runway can reduce the usable crosswind.
- Which direction does a crosswind come from?
- A crosswind comes from the side of the runway, to the left or to the right of the aircraft. Wind direction is the direction that the wind blows from. A wind from 090 degrees blows from the east. On a runway with a heading of 180 degrees, that wind is a full crosswind from the left.
- How does a crosswind affect runway orientation?
- Planners orient runways so that crosswinds rarely stop operations. ICAO recommends that the runways of an aerodrome give a usability factor of at least 95 percent for the aeroplanes that the aerodrome serves. The usability factor is the percentage of time that the crosswind component does not restrict a runway.
References
- faa-ac-150-5300-13b
- AC 150/5300-13B, Airport Design FAA
- easa-ear-aerodromes
- Easy Access Rules for Aerodromes (Regulation (EU) No 139/2014), including CS-ADR-DSN Issue 7 EASA
- icao-annex-14-vol-i
- Annex 14 Volume I, Aerodrome Design and Operations, 9th edition (July 2022) ICAO (copy hosted by the Swiss FOCA)
- ecfr-14-cfr-25-237
- 14 CFR 25.237, Wind velocities US Government Publishing Office (eCFR)
This is a reference entry. TarmacView provides drone inspection services and doesn't sell the equipment or materials described in this glossary.

